All post of ElecFreaksNew ProductTFT01 LCD

New product post 60 – TFT LCD: 1.8 – 2.8

By July 18, 2013 2 Comments
2.8_A

In the previous blog, we made a commitment that this week we would release another series of new products, that is, the TFT LCD series, including 2.8’’ TFT LCD: TFT01-2.8 , 1.8’’ TFT LCD: TFT01-1.8SP , 2.2’ TFT LCD: TFT01-2.2SP , 2.2’’ TFT LCD: TFT01-2.2. TFT LCD module has always been one of the hot products in DIY industry and LCD is basically the necessity during all projects, therefore, carefully compare these features and parameters, at last, take suitable one home.

 

2.8’’ TFT LCD: TFT01-2.8

Feature:

  • TFT01_2.8 is a 2.8″TFT LCD Screen Module , 40pins interface , not just a LCD break but include SD card , and touch panel.
  • VCC 3.3V and Backlight LED 3.3V
  • Touch panel, control ic AD7843,
  • The LCD in the TFT01 is ILI9325D. It’s 240*320(resolution), the contrast is also very suitable.
  • t’s a support 16bit data interface , easy to drive by many MCU like Arduino ,STM32 ,AVR and 8051.
  • The TFT01_2.8 layout a 40 pins interface for your project , the interface include LCD bus, SD card bus, Touch screen bus and the Flash bus.
  • And we have TFT01 Shield and TFT01 MEGA shield, you can directly plug the TFT01 LCD module in the shield and stand on the Arduino board.

Parameter:

  • Display Size:2.8
  • Display Resolution:240 * 320
  • Display Interface:Parallel 16 Bit
  • Display Controller :ILI9325D
  • Expand:SD Card Socket
  • Board Size:65 x 50mm
  • Weight:60.00g

1.8’’ TFT LCD: TFT01-1.8SP

Feature:

  • TFT01_1.8 SP is a 1.8 “SPI TFT LCD Screen Module, 9pins interface, compatible LCD5110 interface. Not just a LCD break but include SD card (2GB),
  • The LCD in the TFT01 is ST7735S. It’s a 128 * 160 (resolution), 1.8 inch TFT LCD screen.The LCD has a wide viewing angle, the contrast is also very suitable.
  • The display interface is serial, it just needs 5 wires (CS, RS, SCL, SDA, RST) for controlling.
  • Replace LCD5110, Support direct plug in ElecFreaks Joystick shield, EFCom, Key Pad Shield etc
  • SDcard use hardware SPI interface (CS / MOSI / MISO / SCK), Not solder pins.

Parameter:

  • LED:3.3V Power Supply pin
  • SCL:Serial clock input
  • SDA/SDI:Serial data input
  • DC:Data/Command selection
  • RST:Reset,Low level active
  • CS:Chip Selection,Low level active
  • GND:Ground
  • VDD33:3.3V Power Supply pi

2.2’ TFT LCD: TFT01-2.2SP

Feature:

  • TFT01_2.2 SP is a 2.2 “SPI TFT LCD Screen Module, 10pins interface, compatible LCD5110 interface. Not just a LCD break but include SD card (2GB),
  • The LCD in the TFT01 is ILI9341. It’s a 240 * 320 (resolution), 2.2S inch TFT LCD screen.The LCD has a wide viewing angle, the contrast is also very suitable.
  • The display interface is serial, it just needs 5 wires (CS, RS, SCL, SDA, RST) for controlling.
  • Replace LCD5110, Support direct plug in ElecFreaks Joystick shield, EFCom, Key Pad Shield etc
  • SDcard use hardware SPI interface (CS / MOSI / MISO / SCK), Not solder pins.

Parameter:

  • SDO: Serial clock output
  • LED: 3.4V Power Supply pin
  • SCL: Serial clock input
  • SDA / SDI: Serial data input
  • DC: Data / Command selection
  • RST: Reset, Low level active
  • CS: Chip Selection, Low level active
  • GND: Ground
  • VDD33: 3.3V Power Supply pin

2.2’’ TFT LCD: TFT01-2.2

Feature:

  • TFT01_2.2 is a 2.2″TFT LCD Screen Module , 40pins interface , not just a LCD break but include SD card , and touch panel.
  • VCC 3.3V and Backlight LED 3.3V
  • The LCD in the TFT01 is S6D0164. It’s 176*220(resolution), the contrast is also very suitable.
  • t’s a support 8bit data interface , easy to drive by many MCU like Arduino ,STM32 ,AVR and 8051.
  • The TFT01_2.2 layout a 40 pins interface for your project , the interface include LCD bus, SD card bus, Touch screen bus and the Flash bus.
  • And we have TFT01 Shield and TFT01 MEGA shield, you can directly plug the TFT01 LCD module in the shield and stand on the Arduino board.

Parameter:

  • Display Size:2.2
  • Display Resolution:176 * 220
  • Display Interface:Parallel 8 Bit
  • Display Controller :S6D0164
  • Expand:SD Card Socket
  • Board Size:65 x 50mm
  • Weight:50.00g

These TFT LCDs integrated features of compact, high resolution, UTFT compatible, supporting TFT01 LCD Shield / TFT01 Mega Shield , and they can be directly used with Arduino, therefore, what are you waiting for? Take one to perfect your cool projects.

VN:F [1.9.13_1145]
Rating: 0.0/10 (0 votes cast)
VN:F [1.9.13_1145]
Rating: 0 (from 0 votes)
dany

Author dany

More posts by dany

Join the discussion 2 Comments

Leave a Reply