cart
item - $0.00

You have no items in your shopping cart.

Subtotal
$0.00

Grid  List 

Set Descending Direction
Page:
  1. 5
  2. 6
  3. 7
  4. 8
  5. 9
  1. Made of silica gel, it can protect micro:bit very well.

    Learn More
  2. micro:bit Wonder Rugged Car(Yellow)(without micro:bit board)

    Learn More
  3. ELECFREAKS Motor:bit for Micro:bit is a kind of motor drive board. It is compatible with micro:bit and can drive 2-channel DC motor at the same time.

    Learn More
  4. OCTOPUS 1Channel Relay is a single relay electronic brick,and its basic design is based on OCTOPUS series products, like shape, PCB positioning holes, interface setting. Adopting Ultra-small, high-quality HUIKE relay, OCTOPUS 1Channel Relay can control various appliances, load high-current, also with opto-isolation, secure and dependable, so Lovers of electronics DIY commonly used it as accessory module. The module is 5V high level trigger, and the trigger current is about 5mA, so almost all of MCU can directly drive it, pull-up not needed.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  5. Crash Sensor Brick is a sensor module based on crash switch, simple circuit design, high sensitivity.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  6. This brick uses the DS18B20 1-Wire digital temperature sensor from Maxim IC. It can report degrees C with 9 to 12-bit precision, -55C to 125C (+/-0.5C). Each sensor has a unique 64-Bit Serial number etched into it that can allow for a huge number of sensors to be used on one data bus.

    This item would be removed off after selling out.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  7. Octopus Tilt Sensor is a sensor based on tilt switch,used together with Arduino specific sensor shield for the measurement of object angle. Three pins electronic building blocks interface: input 5V - GND. S for the detection pin.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  8. OCTOPUS Sound Sensor is a sensor module based on MIC sound sensing element . Sound Sensor is particularly sensitive to sound intensity,and it can be used to detect ambient sound level, but it can not identify the size of sound and the specific sound frequencies. It is available to make voice switches and other works.

     This item would be removed off after selling out.

     

     

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  9. Photo Interrupter Sensor is a sensor module based on ITR9608 photoelectric switch, together with special Arduino shield in use.It has been widely used in parts counting, motor speed and so on. Three pins electronic building blocks interface, input 5V - GND, S for digital signal output.

    This item would be removed off after selling out.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  10. Octopus Hunt Sensor is a sensor based on TCRT5000 photoelectric sensitive element.It can sensitively detect the infrared reflected signal. Together with Arduino specific sensor shield, Hunt Sensor can be widely used in many fields, ranging from performing black and white line detection, obstacle detection , to shredding detection for fax machine or paper shredder, meter pulse data sampling and other related works Adjustable sensitivity (shown in blue digital potentiometer adjustment). Three pins electronic building blocks interface: input 5V - GND. S pin output digital voltage signal 0-1 Operating voltage: DC 5.0V.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More

Grid  List 

Set Descending Direction
Page:
  1. 5
  2. 6
  3. 7
  4. 8
  5. 9