cart
item - $0.00

You have no items in your shopping cart.

Subtotal
$0.00

For micro:bit

Grid  List 

Set Descending Direction
Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  1. Octopus Single RGB Rainbow LED is one of the single rainbow LED electronic bricks in OCTOPUS series. The basic design is upon the OCTOPUS electronic bricks series with the identical design on the outlook, PCB fixed orifices and the connectors of the electronic bricks.

    Learn More
  2. OCTOPUS Magnetic Switch is a simple electric brick module with magnetic control switch.It is normally combined with electromagnet or components with magnet.It can be used to security alarming system´╝îdoor magnetic switch and so on.

    This item would be removed off after selling out.

    Learn More
  3. Octopus 5mmLED light Brick, and special sensors Arduino board and ambient light sensor extension combination, can be used in the interaction with the light works. When the LED light module connected to Arduino, the digital pin (LOW on, HIGH off) is used to control it. The brightness of LED can be controlled via PWM output.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  4. Octopus 5mmLED light Brick, and special sensors Arduino board and ambient light sensor extension combination, can be used in the interaction with the light works. When the LED light module connected to Arduino, the digital pin (LOW on, HIGH off) is used to control it. The brightness of LED can be controlled via PWM output.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  5. Octopus Piranha LED light Brick, and special sensors Arduino board and ambient light sensor extension combination, can be used in the interaction with the light works. When the LED light moduleduino, the digital pin (LOW on, HIGH off) is used to control it. The brightness of LED can be controlled via PWM output.

    This item would be removed off after selling out.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  6. Octopus 5mmLED light Brick, and special sensors Arduino board and ambient light sensor extension combination, can be used in the interaction with the light works. When the LED light module connected to Arduino, the digital pin (LOW on, HIGH off) is used to control it. The brightness of LED can be controlled via PWM output.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  7. Octopus 5mmLED light Brick, and special sensors Arduino board and ambient light sensor extension combination, can be used in the interaction with the light works. When the LED light module connected to Arduino, the digital pin (LOW on, HIGH off) is used to control it. The brightness of LED can be controlled via PWM output.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  8. OCTOPUS Potentiometer is a simple linear sliding potentiometer electronic building block module which can be used for resistor divider output, HID control panel, electronic building block kit.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  9. These displays are small, only about 1" diameter, but very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this miniature display for its crispness! The design is completely 5V-ready, with an onboard regulator and built in boost converter. It's easier than ever to connect directly to your 3V or 5V microcontroller without needing any kind of level shifter! Learn More
  10. OCTOPUS Motor Brick is a type of simple electronic building blocks of the fan motor drive module, it can be used as simple Arduino teaching demo, convenient for  Arduino beginners to learn.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More

Grid  List 

Set Descending Direction
Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5