cart
item - $0.00

You have no items in your shopping cart.

Subtotal
$0.00
Subscribe to RSS Feed

Octopus Bricks

Grid  List 

Set Descending Direction
Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  1. Octopus Electronic Bricks, you can use them build electronics projects just as easy as piling bricks. By using Octopus electronic bricks, you may connect Arduino/Freaduino compatible boards easily with various digital, analog and I2C/Uart interfaces. These the breadboard-less firm connection are prepared to extensive modules like poteniometers, sensors, relays, servos…even buttons, just plug and play.

    This item would be removed off after selling out.

    Learn More
  2. OCTOPUS GAS Sensor MQ3 is a type of electronic building blocks based on alcohol sensor MQ3, used to detect alcohol concentration.

    This item would be removed off after selling out.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  3. These displays are small, only about 1" diameter, but very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this miniature display for its crispness! The design is completely 5V-ready, with an onboard regulator and built in boost converter. It's easier than ever to connect directly to your 3V or 5V microcontroller without needing any kind of level shifter! Learn More
  4. OCTOPUS Potentiometer is a simple linear sliding potentiometer electronic building block module which can be used for resistor divider output, HID control panel, electronic building block kit.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  5. Octopus 5mmLED light Brick, and special sensors Arduino board and ambient light sensor extension combination, can be used in the interaction with the light works. When the LED light module connected to Arduino, the digital pin (LOW on, HIGH off) is used to control it. The brightness of LED can be controlled via PWM output.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  6. Octopus 5mmLED light Brick, and special sensors Arduino board and ambient light sensor extension combination, can be used in the interaction with the light works. When the LED light module connected to Arduino, the digital pin (LOW on, HIGH off) is used to control it. The brightness of LED can be controlled via PWM output.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  7. Octopus Piranha LED light Brick, and special sensors Arduino board and ambient light sensor extension combination, can be used in the interaction with the light works. When the LED light moduleduino, the digital pin (LOW on, HIGH off) is used to control it. The brightness of LED can be controlled via PWM output.

    This item would be removed off after selling out.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  8. Octopus 5mmLED light Brick, and special sensors Arduino board and ambient light sensor extension combination, can be used in the interaction with the light works. When the LED light module connected to Arduino, the digital pin (LOW on, HIGH off) is used to control it. The brightness of LED can be controlled via PWM output.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  9. Octopus 5mmLED light Brick, and special sensors Arduino board and ambient light sensor extension combination, can be used in the interaction with the light works. When the LED light module connected to Arduino, the digital pin (LOW on, HIGH off) is used to control it. The brightness of LED can be controlled via PWM output.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More
  10. Octopus Piranha LED light Brick, and special sensors Arduino board and ambient light sensor extension combination, can be used in the interaction with the light works. When the LED light moduleduino, the digital pin (LOW on, HIGH off) is used to control it. The brightness of LED can be controlled via PWM output.

    This item would be removed off after selling out.

    News: All of Octopus bricks has supported Scratch programming. ElecFreaks builded EFBlock support drag and drop programming . Guide please check here

    Learn More

Grid  List 

Set Descending Direction
Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5